Move Roomba To A New Location

Author: admin December 13, 2022 05:52 December 13, 2022 14 views

Did your Roomba just beep at y'all and requite y'all a dreaded error lawmaking? Don’t freak out! Some errors are easily corrected. Bank check out this detailed guide for information on troubleshooting your Roomba.

Unlike models have slightly dissimilar behaviors when it comes to displaying the error codes: some just beep, some announce the error in bodily words. But fortunately, the error codes themselves are generally identical between the different models.

The following error codes employ to
Roomba Series 500, 600, 700, and 800:

Cleaning Errors

1 Beep / Error 1 (Roomba 500 and 600 Series)

The Roomba says “Fault 1: Motion Roomba to a new location so press Clean to first.” This is normally due to the Roomba getting stuck or a side cycle hanging.

How to Gear up: Turn the Roomba over and examine the side wheels, clear any stuck hair or droppings and button on the wheels to make sure they tin can retract and extend freely. Finally, relocate your Roomba and press clean to bank check if the error has been corrected.

ane Beep or “No Voice” Error (Roomba 700 and 800 Series)

Make sure the grit bin is properly placed back in the Roomba.

2 Beeps / Error 2

The Roomba says “Error ii: Open Roomba’south brush cage and clean brushes.” If you are getting this mistake, the nearly likely culprit is hair stuck on the brushes. It may be that you are not cleaning the brushes of your Roomba often enough, and hair is preventing the brushes from spinning properly.

How to Fix: Extract the hair by following the instructions in this video:

Tip: Information technology is rather tedious to clean the brushes on the older models. Newer Roomba models like the 860 and 960 have replaced the old style brushes with a bristle-less rollers, making Roomba maintenance much simpler.

5 Beeps / Error 5

The Roomba volition denote “Error v: Spin Roomba’s side wheels to clean.” This fault indicates that one of the wheels is stuck, which may exist be due to an obstruction to one of the wheels.

How to gear up: clear whatever pilus and debris out of the wheels and test that the wheels tin can spin freely.

six Beeps / Error six

The Roomba says “Fault half dozen: Move Roomba to a new location then press Clean to restart.” This happens in i of the following situations: (1) the cliff sensors may exist dirty or (ii) Roomba is stuck, on the edge of a cliff, or on a dark surface (which looks like a cliff to the Roomba).

How to set up: clean the cliff sensors with a cloth wipe or nail it with compressed air, then but move the Roomba to a new location and press Clean to restart it.

seven Beeps / Error 7

I of the side wheels is stuck.

How to Ready: Bank check them for obstructions, clear the obstructions, and push the wheels upward and downward to loosen any debris. Manually plow the wheels to make sure they move freely.

9 Beeps / Error 9

The Roomba will say “Error 9: Tap Roomba’s bumpers to clean.” This happens when the bumpers sensors are dingy or the area between the Roomba unit and the bumpers is dirty.

How to prepare: first, tap on the bumper several times to loosen whatever droppings and make sure information technology is able to spring back into place. If this does not ready the error, you may demand to clean the area betwixt the bumpers and the Roomba unit of measurement. This will clear any droppings and also clean the bumper sensors.

10 Beeps / Error ten

“Mistake ten: Spin Roomba’s side wheels to clean.” This ways that the side wheels on the Roomba (the ii large wheels) are unable to spin or that the Roomba is stuck on something.

How to fix: If the Roomba is stuck somewhere, simply move it to a new location and press Clean to reset it. Otherwise, check that the side wheels have no obstructions preventing them from spinning. Push button the wheels in and out to loosen any debris, and plough the wheels by hand to make sure that they are not stuck on something (e.yard. hair).

This mistake could likewise arise if yous take a large, open up area in your firm with very few items. To remedy this, use Virtual Walls to divide the big area into several smaller areas. For more details on this outcome: see this forum post.

11 Beeps / Fault 11

“Mistake xi” is in essense the aforementioned error as Mistake 10.

4 Tone Expressionless Battery Sound

“Please charge the Roomba”.

How to Fix: fully charge the Roomba. Also, follow these steps to lengthen the life of your Roomba’s battery:

Recharge the Roomba as soon as possible subsequently every use. If your Roomba has auto-docking, this will happen automatically. Try not to go out the Roomba discharged after vacuuming.
Use the Roomba regularly. The batteries are designed to be discharged and recharged frequently, so use it frequently.
Keep the docking station plugged in and the Roomba docked when not in use.
Finally, if you won’t be using the Roomba for more than a few weeks, take out the battery and store it somewhere dry and cool.

“Please Inspect and Clean Roomba’s Cliff Sensors”

Like to error 6, the cliff sensors may need to be cleaned or replaced. Wipe the cliff sensors with a damp cloth to clean them. See error half dozen above for details.

“Please Inspect and Clean Roomba’due south Wheels”

One of the side wheels is likely stuck. Make sure there are no obstructions preventing the side wheels from spinning. Push the wheels in and out to loosen any debris, and plough the wheels by paw to make sure that they are non stuck on hair or dustballs. Run across Error 10 for details.

“Delight Remove and Clean Roomba’due south Brushes”

The spinning brushes are unable to turn. This is usually due to something like hair getting stuck in the brushes. Take out the spinning brushes or rollers underneath the Roomba every bit shown in this iRobot video, clear information technology of whatsoever obstructions, then put the brushes back in place. In the future, do this regularly before the mistake occurs to ensure a long life for your Roomba. If you find this tedious, the newer, brush-less Roomba models are less prone to having hair go stuck to them.

Roomba Returns to Dock Too Early on with Full Battery

Confirm that the battery is not low. The battery indicator on the Roomba unit of measurement will glow greenish if fully charged. If and so, reset the Roomba:

Roomba 500 and 600: Press and hold the SPOT and DOCK buttons for approximately ten seconds.

Roomba 700 and 800: Press and hold the Make clean button for approximately x seconds, the unit will brandish “RST”.

After doing this, you will need to reprogram the time, appointment, and also the rescheduled cleanings.

Charging Errors

one Blink or Charging Error 1

The battery is non connected. Make certain the battery is seated correctly. If your Roomba is brand new, it means you lot did not pull out the plastic tabs blocking the batteries.

two Blinks or Charging Error Two

The current to the battery is besides high. This mistake requires service past the manufacturer, but in a last ditch effort you may attempt moving the Roomba to somewhere cooler to allow it to cool down.

3 Blinks or Charging Error Three

This charging error commonly requires service by the manufacturer. However, information technology may also but mean that the bombardment contacts do not have proficient contact with the battery. For the particularly audacious, remove the batteries and try to bend the large contacts and try charging again.

5 Blinks or Charging Error Five

Starting time cheque the battery and charging contacts. Remove the screws on the lesser of the Roomba to open up the bombardment door. Locate the contacts as shown below, and wipe them make clean with a dry cloth or dry out rubber eraser. Also practice the same for the charging contacts on the domicile base.

Motion the home base to somewhere cooler to make certain charging the Roomba does not cause it to overheat. Likewise, the home base should be placed on a difficult, even surface to ensure the contacts are properly aligned.

vi Blinks or Charging Error 6

The bombardment has overheated. This mistake occurs when the bombardment temperature reaches 75°C. Move the home base to a cooler surroundings. Make certain nothing is sitting on top of the Roomba while it charges.

7 Blinks or Charging Error Seven

Battery is unable to cool. This error occurs when the battery doesn’t absurd down within 4 hours afterward charging or after use. Let the Roomba cool down for at least one hr, then accuse it in a cooler surround.If the trouble persists, the battery may demand to be replaced.